ALTEX COATINGS INDUSTRIAL & MARINE AF3000 ANTI-FOULING

País: Austrália

Língua: inglês

Origem: APVMA (Australian Pesticides and Veterinary Medicines Authority)

Ingredientes ativos:

THIRAM; COPPER PRESENT AS CUPROUS OXIDE; ZINC AS ZINC OXIDE; XYLENE

Disponível em:

RESENE PAINTS (AUSTRALIA) LIMITED

DCI (Denominação Comum Internacional):

Cu as cuprous oxide(764g/L)+Zn as oxide(196g/L)+thiram(44g/L)

Forma farmacêutica:

PAINT

Composição:

THIRAM CARBAMATE-DITHIOCARBAMATE Active 44.0 g/L; COPPER PRESENT AS CUPROUS OXIDE MINERAL-COPPER Active 764.0 g/L; ZINC AS ZINC OXIDE MINERAL-ZINC Active 196.0 g/L; XYLENE SOLVENT Other 163.0 g/L

Unidades em pacote:

10L; 4L

Classe:

A - Agricultural

Fabricado por:

RESENE PAINTS

Grupo terapêutico:

BOAT - EXTERIOR (ANTIFOULING)

Área terapêutica:

ANTIFOULING

Indicações terapêuticas:

FOULING - FOR ANTIFOULING ON BOATS

Resumo do produto:

Poison schedule: 6; Withholding period: WHP: N/A.; Host/pest details: BOAT - EXTERIOR (ANTIFOULING): [FOULING - FOR ANTIFOULING ON BOATS]; Poison schedule: 6; Withholding period: ; Host/pest details: BOAT - EXTERIOR (ANTIFOULING): [FOULING - FOR ANTIFOULING ON BOATS]; An ablative antifouling for use on suitably prepared steel, fibreglass, ferro cement, and wooden hulls.DO NOT use on aluminium hulls or stern drives

Status de autorização:

Stopped

Data de autorização:

2022-07-01

Folheto informativo - Bula

REFER TO RELEVANT PRODUCT DATA SHEET BEFORE MIXING OR APPLICATION OF
COATINGS.
DIRECTIONS FOR USE
RESTRAINTS: DO NOT use on aluminium
hulls or stern drives.
SURFACE PREPARATION: AF 3000 Antifouling
paint is designed to overcoat Altex Coatings Bottom
Systems. AF 3000 Antifouling is compatible with a
wide range of anticorrosive and antifouling paints.
Its use over products other than Altex Coatings
Bottom Systems should be referred to Resene Paints
(Australia) Limited for specific recommendations. If
AF 3000 Antifouling is applied over an epoxy hull
coating, it must be applied before the epoxy has fully
cured hard, i.e. when the epoxy is tack free but still
soft to finger nail pressure. For the repainting of
existing antifouling and to facilitate bottom cleaning
we recommend high pressure water blast cleaning
(5000 p.s.i. minimum) and wash with Devprep 88
diluted 1 part to 10 parts water. It is recommended
that after 3 to 4 repaints that the old antifouling
coatings be removed and then repaint the hull with
Altex Coatings Bottom System and AF 3000
Antifouling as above.
MIXING AND THINNING: Stir thoroughly before
use. AF 3000 Antifouling does not require thinning,
except possibly in hot windy conditions. If thinned,
additional coats may be required to attain correct
film thickness. Film thickness is
critical to the
performance life of the coating.
APPLICATION: Apply 2 coats to achieve a
minimum total dry film thickness of 200 microns.
AF 3000 Antifouling can be brushed, rolled and air
sprayed, however, it is strongly recommended that
application is by heavy duty airless spray equipment
(pump ratio 30:1, tip size .021 to .025). For
multicoat application of AF 3000 Antifouling use
contrasting colours as a further assurance that the
proper film thickness is applied. Film thickness control
is
critical. NOT TO BE USED FOR ANY PURPOSE OR IN
ANY MANNER CONTRARY TO THIS LABEL UNLESS
AUTHORISED UNDER APPROPRIATE LEGISLATION.
Poisonous if swallowed. Will irritate the eyes, and
skin. Avoid breathing dust, vapour or spray mist.

Características técnicas

MSDS: AF3000 Antifouling
Page 1 of 8
Prepared: 28/10/09 Revision: 2
nd
Revision
Printed:27/01/11
Resene Paints (Australia) Limited trading as Altex Coatings.
MATERIAL SAFETY DATA SHEET
SECTION 1.
IDENTIFICATION OF THE MATERIAL AND SUPPLIER
PRODUCT NAME
AF3000 ANTIFOULING
OTHER NAMES
Paint. Product Code AF3--S
RECOMMENDED USE
High performance, ablative antifouling coating.
COMPANY NAME
ADDRESS
Resene Paints (Australia) Limited T/A Altex Coatings.
7 Production Avenue
Ernest Junction, Queensland 4214.
EMERGENCY TEL
Available Monday – Friday, 8:00 a.m. – 5:00 p.m.
FREE CALL
PHONE
FAX
1800 738 383
07 5512 6600
07 5512 6698
SECTION 2.
HAZARDS IDENTIFICATION
HAZARD CLASSIFICATION
HAZARDOUS SUBSTANCE. DANGEROUS GOODS. According
to the criteria of NOHSC and the ADG Code.
HAZARD STATEMENTS
Xn: Harmful
N: Dangerous for the environment
RISK PHRASES
R10 Flammable.
R20/21/22 Harmful by inhalation, in contact with skin and if
swallowed.
R36/37/38 Irritating to eyes, respiratory system and skin.
R40 Limited evidence of a carcinogenic effect.
R41 Risk of serious damage to the eyes.
R43 May cause sensitisation by skin contact.
R67 Vapours may cause drowsiness and dizziness.
R50 Very toxic to aquatic organisms.
R53 May cause long term adverse effects in the aquatic environment.
SAFETY PHRASES
S7/9 Keep container tightly closed and in a well-ventilated place.
S13 Keep away from food, drink and animal feeding stuffs.
S16 Keep away from source of ignition-No smoking.
S23 Do not breathe gas/fumes/vapour/spray.
S24/25 Avoid contact with skin and eyes.
S26 In case of contact with the eyes, rinse immediately with plenty of
water and seek
medical advice.
S36/37/39 Wear suitable protective clothing, gloves and eye/face
protection.
S46 If swallowed, seek medical advice immediately and show this
container or label.
S60 This material and its container must be disposed of as hazardous
waste.
S61 Avoid release to the environment. Refer to special
instructions/Material Safety
Data Sheets.
MSDS: AF3000 Antifouling
Page 2 of 8
Prepared: 28/10/0