Valsts: Austrālija
Valoda: angļu
Klimata pārmaiņas: APVMA (Australian Pesticides and Veterinary Medicines Authority)
THIRAM; COPPER PRESENT AS CUPROUS OXIDE; ZINC AS ZINC OXIDE; XYLENE
RESENE PAINTS (AUSTRALIA) LIMITED
Cu as cuprous oxide(764g/L)+Zn as oxide(196g/L)+thiram(44g/L)
PAINT
THIRAM CARBAMATE-DITHIOCARBAMATE Active 44.0 g/L; COPPER PRESENT AS CUPROUS OXIDE MINERAL-COPPER Active 764.0 g/L; ZINC AS ZINC OXIDE MINERAL-ZINC Active 196.0 g/L; XYLENE SOLVENT Other 163.0 g/L
10L; 4L
A - Agricultural
RESENE PAINTS
BOAT - EXTERIOR (ANTIFOULING)
ANTIFOULING
FOULING - FOR ANTIFOULING ON BOATS
Poison schedule: 6; Withholding period: WHP: N/A.; Host/pest details: BOAT - EXTERIOR (ANTIFOULING): [FOULING - FOR ANTIFOULING ON BOATS]; Poison schedule: 6; Withholding period: ; Host/pest details: BOAT - EXTERIOR (ANTIFOULING): [FOULING - FOR ANTIFOULING ON BOATS]; An ablative antifouling for use on suitably prepared steel, fibreglass, ferro cement, and wooden hulls.DO NOT use on aluminium hulls or stern drives
Stopped
2022-07-01
REFER TO RELEVANT PRODUCT DATA SHEET BEFORE MIXING OR APPLICATION OF COATINGS. DIRECTIONS FOR USE RESTRAINTS: DO NOT use on aluminium hulls or stern drives. SURFACE PREPARATION: AF 3000 Antifouling paint is designed to overcoat Altex Coatings Bottom Systems. AF 3000 Antifouling is compatible with a wide range of anticorrosive and antifouling paints. Its use over products other than Altex Coatings Bottom Systems should be referred to Resene Paints (Australia) Limited for specific recommendations. If AF 3000 Antifouling is applied over an epoxy hull coating, it must be applied before the epoxy has fully cured hard, i.e. when the epoxy is tack free but still soft to finger nail pressure. For the repainting of existing antifouling and to facilitate bottom cleaning we recommend high pressure water blast cleaning (5000 p.s.i. minimum) and wash with Devprep 88 diluted 1 part to 10 parts water. It is recommended that after 3 to 4 repaints that the old antifouling coatings be removed and then repaint the hull with Altex Coatings Bottom System and AF 3000 Antifouling as above. MIXING AND THINNING: Stir thoroughly before use. AF 3000 Antifouling does not require thinning, except possibly in hot windy conditions. If thinned, additional coats may be required to attain correct film thickness. Film thickness is critical to the performance life of the coating. APPLICATION: Apply 2 coats to achieve a minimum total dry film thickness of 200 microns. AF 3000 Antifouling can be brushed, rolled and air sprayed, however, it is strongly recommended that application is by heavy duty airless spray equipment (pump ratio 30:1, tip size .021 to .025). For multicoat application of AF 3000 Antifouling use contrasting colours as a further assurance that the proper film thickness is applied. Film thickness control is critical. NOT TO BE USED FOR ANY PURPOSE OR IN ANY MANNER CONTRARY TO THIS LABEL UNLESS AUTHORISED UNDER APPROPRIATE LEGISLATION. Poisonous if swallowed. Will irritate the eyes, and skin. Avoid breathing dust, vapour or spray mist. Izlasiet visu dokumentu
MSDS: AF3000 Antifouling Page 1 of 8 Prepared: 28/10/09 Revision: 2 nd Revision Printed:27/01/11 Resene Paints (Australia) Limited trading as Altex Coatings. MATERIAL SAFETY DATA SHEET SECTION 1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER PRODUCT NAME AF3000 ANTIFOULING OTHER NAMES Paint. Product Code AF3--S RECOMMENDED USE High performance, ablative antifouling coating. COMPANY NAME ADDRESS Resene Paints (Australia) Limited T/A Altex Coatings. 7 Production Avenue Ernest Junction, Queensland 4214. EMERGENCY TEL Available Monday – Friday, 8:00 a.m. – 5:00 p.m. FREE CALL PHONE FAX 1800 738 383 07 5512 6600 07 5512 6698 SECTION 2. HAZARDS IDENTIFICATION HAZARD CLASSIFICATION HAZARDOUS SUBSTANCE. DANGEROUS GOODS. According to the criteria of NOHSC and the ADG Code. HAZARD STATEMENTS Xn: Harmful N: Dangerous for the environment RISK PHRASES R10 Flammable. R20/21/22 Harmful by inhalation, in contact with skin and if swallowed. R36/37/38 Irritating to eyes, respiratory system and skin. R40 Limited evidence of a carcinogenic effect. R41 Risk of serious damage to the eyes. R43 May cause sensitisation by skin contact. R67 Vapours may cause drowsiness and dizziness. R50 Very toxic to aquatic organisms. R53 May cause long term adverse effects in the aquatic environment. SAFETY PHRASES S7/9 Keep container tightly closed and in a well-ventilated place. S13 Keep away from food, drink and animal feeding stuffs. S16 Keep away from source of ignition-No smoking. S23 Do not breathe gas/fumes/vapour/spray. S24/25 Avoid contact with skin and eyes. S26 In case of contact with the eyes, rinse immediately with plenty of water and seek medical advice. S36/37/39 Wear suitable protective clothing, gloves and eye/face protection. S46 If swallowed, seek medical advice immediately and show this container or label. S60 This material and its container must be disposed of as hazardous waste. S61 Avoid release to the environment. Refer to special instructions/Material Safety Data Sheets. MSDS: AF3000 Antifouling Page 2 of 8 Prepared: 28/10/0 Izlasiet visu dokumentu