VALIANT EXPRESS PRIME- lactic acid solution

Country: United States

Language: English

Source: NLM (National Library of Medicine)

Active ingredient:

LACTIC ACID (UNII: 33X04XA5AT) (LACTIC ACID - UNII:33X04XA5AT)

Available from:

ABS Global

INN (International Name):

LACTIC ACID

Composition:

LACTIC ACID 80 mg in 1 mL

Administration route:

TOPICAL

Prescription type:

OTC

Therapeutic indications:

DIRECTIONS FOR USE Mix Directions: If not using an automated pump system, then mix according to the following directions. 1. Measure one part of Express Prime component into a clean empty, non-metallic container. 2. Add 20 parts cool potable water (at or below 77°F/25°C.) 3. Add one part Express 3 Concentrate component and mix. 4. This mixed solution Express Prime & 3 RTU (ready-to-use) will remain stable for 24 hours. After 24 hours discard any remaining solution and mix a new solution. IMPORTANT: Do not add mixed Express Prime & 3 RTU ready-to-use to any other teat dip or other products. If transferred from this container to any other, make sure the other container is thoroughly pre-cleaned and bears the proper container labeling for Express Prime & 3 RTU. Use of a complete cow-care program including both pre and post dipping may aid in reducing the spread of organisms which may cause mastitis. DIRECTIONS FOR TEAT DIPPING Pre-Milking: Fill teat dip cup with Express Prime & 3 RTU. Before each cow is milke

Authorization status:

unapproved drug other

Summary of Product characteristics

VALIANT EXPRESS PRIME- LACTIC ACID SOLUTION
ABS GLOBAL
_Disclaimer: This drug has not been found by FDA to be safe and
effective, and this labeling has not been_
_approved by FDA. For further information about unapproved drugs,
click here._
----------
KEEP OUT OF REACH OF CHILDREN
NOT FOR HUMAN USE
WARNING
Causes eye irritation.
Wash skin thoroughly after handling.
Do not mix with bleach or other chlorinated products – will cause
chlorine gas.
DIRECTIONS FOR USE
MIX DIRECTIONS: If not using an automated pump system, then mix
according to the following directions.
1. Measure one part of Express Prime component into a clean empty,
non-metallic container.
2. Add 20 parts cool potable water (at or below 77°F/25°C.)
3. Add one part Express 3 Concentrate component and mix.
4. This mixed solution Express Prime & 3 RTU (ready-to-use) will
remain stable for 24 hours. After
24 hours discard any remaining solution and mix a new solution.
IMPORTANT: Do not add mixed Express Prime & 3 RTU ready-to-use to any
other teat dip or other
products. If transferred from this container to any other, make sure
the other container is thoroughly
pre-cleaned and bears the proper container labeling for Express Prime
& 3 RTU. Use of a complete
cow-care program including both pre and post dipping may aid in
reducing the spread of organisms
which may cause mastitis.
DIRECTIONS FOR TEAT DIPPING
PRE-MILKING: Fill teat dip cup with Express Prime & 3 RTU. Before each
cow is milked, dip the teats as
far as possible into the teat dip cup containing Express Prime & 3
RTU. Wipe teats dry after dipping,
using single-service towels to avoid contamination of milk. Udder and
teats which are heavily soiled
should be washed before using a pre-milking teat dip. Teats should be
dried with a single-service
towel and dipped in Express Prime & 3 RTU, wiping teats dry before
milking.
POST-MILKING: Immediately after milking, use Express Prime & 3 RTU at
full strength. Submerge teat
2/3 their length in Express Prime & 3 RTU teat dip. Allow to air dry.
Do not wi